Specialty pages:

Sportster Section

Buell parts

V-Rod parts

Chain and Belt Laser Alignment Tool

• Easy to use laser tool shows exact alignment of the drive chain or drive belt.
• Includes common type batteries, storage bag and instructions.

Part#:MU70443 ... Price: $108.92 including shipping*

IGNITION TIMING TOOL FOR BIG TWIN - Rite-On-Time

Designed for Ignition Systems that have points or electronic ignition with mechanical-type advance unit.
Allows timing light to be used on the right hand side of the motorcycle.
Turns a two-man-job into a one-man-job.
Shows exact amount of advance in degrees and will show over advance if the advance unit is worn out.
Stainless steel construction.
Includes instructions and storage case.

Fits Big Twin 1970/1999 (Except EFI & Twin Cam), Part#:MU10610 ... $118.41 including free shipping*

PRIMARY COVER NEEDLE BEARING PULLER FOR BIG TWIN & SPORTSTER - Jims


What was once a difficult bearing to remove can now be done with the greatest of ease. Made with Aerospace steel. Includes Instructions. Fits Big Twin 1965/1988 and Sportster 1967/1980. Made in the U.S.A. by Jims.

Part#:MU70440 ... $151.26 including shipping*

• HD bearing 9063 (our MU67504) found in the outer primary cover to support the starter shaft on Big Twin 1965/1988 and Sportster 1967/1980.
• HD bearing 35961-52 (our MU72930) found in the 4 speed transmission countershaft gear on Big Twin Late 1967/Later, the clutch gear on Sportster 4 speed, all years, and the access door on Sportster 4 speed, all years.

MAIN DRIVE GEAR AND BEARING TOOL FOR 5 & 6 SPEED TRANSMISSIONS - Baker

• Required for removing and installing the main drive gear and main bearing from the case
• Can be used without removing the transmission case from the motorcycle
• Will not damage the main bearing upon removal
• Includes instructions
• Made in the U.S.A. by Baker Drivetrain

Part#:MU70446 - Fits Big Twin 5 and 6 Speed 1980/Later & Sportster 1991/Later ... $278.30 including free shipping*

Deep Well Sockets with T- Handles

DEEP WELL SOCKETS WITH T-HANDLES by Motion Pro

12 point design includes 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16" & 3/4". Shaft & socket portion measures 12" and is made from chrome-vanadium tool steel for strength. Handles measure 8" for good control and are made from carbon steel. Socket O.D. is kept as slim as possible to access tight areas. Partial length hex prevents nuts from being pushed too deep into socket. Manufacturer's lifetime warranty.

Deep well sockets with t-handles. Part#:MU07502 ... Price: $104.15 including free shipping*

Don't get stuck on the side of the road!

Makes a great gift!

ROADSIDE TOOL KITS

These Econokits from CruzTools include the most commonly needed tools for roadside repair in a 23 piece kit with a roll-up type case. The kit measures 10" x 3" when rolled up. Feature pouches and elastic straps to hold the tools securely in place to prevent the tools from rattling. The case is made from a 600 denier polyester that is vinyl backed and double paneled for years of service.

23 Piece Kit with roll up Case - Part#:MU07511 ... $87.75 including shipping*

Included in Case 23 Piece Kit:
Combination Wrenches 10mm, 3/8", 7/16", 1/2", & 9/16"
Adjustable Wrench 8" length (opens to 15/16")
Locking Pliers 6" length with coarse & fine teeth
Allen Wrenches 1/8", 5/32", 3/16", 1/4" & 5/16"
Torx Wrenches T25, T27, & T40
Phillips Screwdrivers #1 & #2
Straight Screw Drivers 3/16" wide & 1/4" wide
Deep Well Nut Drivers 1/4" & 5/16"
Spark Plug Sockets 13/16" & 5/8"
Spark Plug gapper .020"/.100" & .6mm/2.4mm
Tire Pressure Gauge 5lbs/50 lbs
Electrical Tape 3/4" wide x 30' long
Wire Ties 5 pieces, 5 1/2" long
Mechanics Wire 3' long
Flashlight Adjustable beam with 2 AA batteries and spare bulb
Thread Locker Medium strength (blue)
Lubricant WD-40 (one time use)
Shop Towel - Measures 12" x 14"

BATTERY CHARGER/MAINTAINER FOR 12 VOLT BATTERIES - Battery Tender®.

BATTERY TENDER by DELTRAN - This is the original 12 volt, 1.25 amp Battery Tender. Designed to fully charge a battery and maintain it at the proper voltage without fear of overcharge. This is done by a 3-step charging program, bulk charge, absorption mode and float mode. It is temperature compensated to endure optimum charge voltage according to the ambient temperature. User safety features include a grounded AC cord and reverse polarity protected quick connect harness system. One harness stays connected to the motorcycle for winter storage and the other includes alligator clips for bench charging. Designed and assembled in the USA. Includes instructions. Measures 4 7/8" x 3 1/4" x 2 7/8".
Part#:MU10513 ... $72.75 including shipping*

SHOCK SPRING COMPRESSOR FOR SOFTAIL 1984/1999 by Progressive Suspension

Used to make a dangerous job simple and safe. This all steel tool includes a welded on tab for mounting in a vise to free up both hands. This ingenious tool is a necessity when installing a lowering kit or rebuilding your rear shocks. Instructions included. Fits all OEM and Progressive Suspension rear shocks for Softail 1984/Later. Made in U.S.A.

Part#:MU20107 ... Price: $95.15 including free shipping*

WHEEL SERVICE CENTER FOR ALL MODELS by Rowe

This multi-purpose wheel tool is a necessity for any self supporting shop or do it yourselfer. It will fit all OE size wheels and most wide tire size wheels. Check & true wheels with up to 1" I.D. bearings. Static balance assembled wheels on the top mounted V slots or use the low drag precision bearings (shown in inset). Free standing steel base can be permanently bench mounted. Adjustable pointer for checking radial & lateral run out. Includes spoke wrench that fits six different size spoke nipples. Made in U.S.A.

Part#:MU57903 ... Price: $507.28 including free shipping*

Part#:MU60888 ... $72.50 includes shipping*

SOLID STICK LOCTITE PRODUCTS - Loctite

Convenient solid stick dispenser provides easy application, storage and will not drip or run.
For best results, use 05227 Locktite Klean 'N Prime Activator (add to kit for a few extra dollars, below. Great deal!)
Part#:MU05400 - Complete Kit of 5 Price ... $107.10 including shipping*

ADD: KLEAN 'N PRIME® ACTIVATOR FOR THREADLOCKER - Loctite
Recommended to properly prepare the surface and ensure a good bond for all threadlockers.
Speeds the cure time.
Ideal for conditions below room temperature.

Part#:MU05227-05400 - 4.5 oz. Aerosol Can Klean 'N Prime (Suggested Retail $15.85) added to above Loctite stick kit. Total for both just $113.69 including shipping* Great deal!

Air Force Blaster® Motorcycle Dryer

• The Blaster® cuts drying time as much as 75%.
• Blows warm, dry, clean, filtered air.
• Eliminates water spots.
• Safter, more effective than compressed air or leaf blowers.
• Prevents rust.
• Lightweight and portable.
• Rugged all steel construction.
• 4.0 peak HP motor.
• 10 ft. heavy-duty hose.
• 4 interchangeable attachments.

#BC498799 - Blaster Motorcycle Dryer ... $228.79 including shipping*

SADDLEBAG STAND - Kick Start Creative


The Saddlebag Stand is compact and easy to use. Simply open the stand and set the saddlebags in place. Requires no assembly or additional hardware. Wash and wax your saddlebags right on the stand. Made in the U.S.A.

Part#:0126776 - Black Powder Coated finish Saddlebag Stand ... $125.25 including shipping*

The Most Useful Tool you can get! Mid-USA's "Just Hard Parts" catalog.

More tools, and every kind of part you need to build, customize or repair your motorcycle. Just $12 with shipping.  You will get the purchase price back with your first order over $100.  We also discount off of the retail price list: 10% off on purchases over $100 and we give free shipping on orders over $295. (Items online have already been discounted.)

Note: Cover may differ from one illustrated.

THE 2008 CATALOGS ARE IN STOCK!

HIGH PROFORMANCE ENGINE/TRANSMISSION/PRIMARY OIL FOR ALL MODELS - Lucas Oil Products

20W-50 Viscosity, Synthetic

Lucas Motorcycle Oil is built for endurance, lasting up to 4 times longer than other brands. It will also lower oil temperatures, extend the life of vital components, reduce noise and leaks and increase performance.
Our SAE 20W-50 is also an excellent gear oil and primary oil.
All Lucas motorcycle oils meet or exceeds: API SG/SF/CC/CD, JASO MA, ACEA A3 specifications. Official oil product of NHRA.
A 100% synthetic oil. Made in the U.S.A.
For use in Evolution & Twin Cam models, and all air-cooled or water-cooled 4-stroke engines calling for a 20W-50 motor oil.

Part#:05021- Lucas Oil, 20W-50 Viscosity, Synthetic, 1 quart bottles, Pack of 6 ( Note: Not Shippable by Air.) ...
$54.00 including free shipping*.