Steel Thunder Custom Cycles motorcycle parts

 

Shopping Pages:

Control Section:

Brakes, discs, rotors, dashes & instrument panels, gauge brackets, footpegs, forward controls, grips, throttle control, handlebar controls, handlebars, levers, linkage, levers, mirrors, risers, shift & jockey control.

Drivetrain Section:

Belt drives, belt drive covers, clutch kits, chain drives, drivetrain packages, kick start transmission, offset sprockets, points, derby & ignition coves, primary belts, primary chains, primary covers, pulley & brake combo kit, rear drive belts, Sportster performance parts, six speed conversion, rear sprockets, rotors, transmissions & parts.

Electrical Section:

Battery related, battery tenders, charging systems,coils & mounts, dash/instrument panels, speedos, tachs, terminal kits, electronic ignitions, handlebar switches, headlights, horns, lighted license plate mounts, lighting, starter motors, taillights, turn signals, wiring harnesses.

Engine Section:

Motorcycle engine parts, drivetrain packages, cams & cam side parts, big bore kits, big bore piston kits, Sportster engine parts, motor mounts, drivetrain section, engine mounts.

Exhaust Section:

Exhaust pipes listed by model, exhaust accessories, insulating wrap, mufflers, extensions, high heat spray, heat shields, clamps and mounts.

Frame/Body Section:

Frames listed by style, engine mounts, fenders, struts, floorboards, foot rests, pegs, frame covers, hardtails, highway bars, kickstands, lowering kits, seats listed by model, shocks, sissy bars & pads, swingarms.. Also, Rolling Chassis Kits.

Front End Section:

Complete front fork assemblies, fairings & fairing accessories, fork brackets/triple trees, fork tubes, sliders, fork legs, boots, springer front ends & parts, wide glide kits.

Fuel Section (Gas, Oil, Air):

Air cleaners & covers, breathers, carburetors & rebuild kits, fuel injection control, gas tanks, gas caps, gas tank cleaner/prep systems, oil, oil coolers, oil line kits, oil pressure & tank gauges, oil pumps, oil tanks, , velocity stacks.

Saddlebag & Windshield Section:

Saddlebags listed by manufacturer, windshields

Wheel Section

Tires,  tire size chart, 40, 60 & 80 spoke wheels, solid wheels.

General Merchandise Section:

Catalogs, covers, gift certificates, gift suggestions, goggles & eyewear, hardware, luggage racks, motors, motorcycle covers, security, locks & alarms, tools, trailer accessories, ramps, wheel chocks, trailer hitches to put on motorcycle.

Other Pages:

Fun, Photos & Links Section:

Photos of our customer's motorcycles, including bike kit builds, trike build link, free biker ecards, jokes, banner links, text links, link to us, webmaster's awards.

Tech & Info Section

Tech tips, tire size chart, engine break-in, suspension & shocks info, rake and trail calculator, contact page, frequently asked questions (FAQ), our credentails, terms & conditions of sale, disclaimer, international shipping policy.

Secured by SSL - an authentic COMOCO site.

 

link

 

 

 

NEW FLAT RATE SHIPPING!  No hidden fees and NO TAX! Only $12.95 in the continental. U.S., no matter how large (or heavy) your order is!  Save $$$ ... order everything you need NOW! 

Announcing NEW HOURS:  Starting Monday July 28th, we will be open Wednesday thru Sunday 10 - 6.
Sitemap and Search Home Page Contact Us Sportster Section Catalogs

Exhaust Pipes for Sportsters®      

S&S Quick Set Up Kits - Exhaust and Air Cleaner kits for bike upgrades, on "air" page.

Exhaust Index - - Sportster Page

Fits 2004/2013 Sportsters

Slash cut drag pipes for 2004 and 2005 Sportster models.  Choose 1 3/4 or 2 inch outside diameter.

CHROME PLATED DRAG PIPE SETS FOR EVOLUTION SPORTSTER 2004 & LATER

Cycle Shack Slash Cut
These 40" long drag pipe sets are available in your choice of 1 3/4" O.D. are designed to be used with the existing OEM exhaust support mount
The 1 3/4" O.D. set can be used with your existing OEM heat shields
The 2" O.D. set includes heat shields

Part#:M90039 - 1 3/4" O.D. - Fits all Sportster Models 2004/L ... $195.69

Part#:M90040 - 2" O.D. - Fits all Sportster Models 2004/L ... $331.16

Fits 2004/2013 Sportsters

40 inch long, 1 3/4 diameter dual exhaust for Evolutions Sportster 2004 & 2005.

CHROME PLATED DUAL EXHAUST FOR EVOLUTION SPORTSTER - Cycle Shack

These 40" Long Dual Exhaust Systems are designed to be used with the existing OEM exhaust mounting bracket.
All steel high-flow baffles.
The 1 3/4" O.D. set can be used with your existing OEM heat shields.

Part#:M91155 - 1 3/4" O.D. - Fits all Sportster Models 2004/2006... $295.87

Rinehart Racing

Fits 2004/2013 Sportsters

SPECIAL:

Free Shipping on this item!

Rinehart Crossback 2 into 2 Exhaust Drag Pipe for Sportster XL 2004 and up.


Chrome Crossback 2 into 2 Exhaust Drag Pipes for Sportster - Rinehart Racing

Chrome Rinehart crossback 2 into 2 exhaust drag pipes include header pipes, staggered mufflers, heat shields, baffles and billet end caps.
They also feature a 3 step header design with 2-1/2" integrated mufflers that boosts torque and horsepower across the RPM range. Includes 2-1/2" header pipes with staggered style mufflers, 220° full coverage heat shields that merge to the muffler bodies, billet end caps and 2 sets of baffles. Baffles have 2" outer diameter for engines up to 96" cubic inches and 2-1/4" outer diameter for large high performance engines. System includes two oxygen sensor ports. **CAUTION: These exhaust products are not legal for sale or use in California on pollution controlled vehicles. These products are intended for non-highway only. Made in the U.S.A.
Part #: V30-1553 - Staggered Style Crossback 2 into 2 Exhaust, Fits: XL 2004/Later ... $900.00 including FREE SHIPPING! (within continental U.S.)


2004 - 2013

SPECIAL:

Free Shipping on this item!

Vance and Hines Side Shots Exhaust Drag Pipes for Sportster Harley-Davidson Motorcycles.

Vance and Hines Drag Pipes for XL (Sportster) up to 2013

Side Shots Exhaust Drag Pipe Set for Sportster - Vance & Hines

Chrome Vance & Hines side shots exhaust feature high style and performance combined with unbeatable value.
Side shots exhaust feature power chamber design, 2-1/2" header pipes, 220° full length heat shields, removable baffles and mounting hardware. Made in the U.S.A.

**CAUTION: These exhaust products are not legal for sale or use in California on pollution controlled vehicles. These products are intended for non-highway only.

Part#: V301528 - Kit fits XL 2004-2006 ...$607.47 including FREE SHIPPING! (within continental U.S.)

Part#: V301536 - Kit fits XL 2007/Later... $695.31 including FREE SHIPPING! (within continental U.S.)

Cycle Shack tapered dual exhaust pipes for Sportster Evo.

Tapered

Cycle Shack Slash Cut  dual exhaust pipes for Sportster Evo.

Slash Cut

DUAL EXHAUST SYSTEMS FOR SPORTSTER EVOLUTION - Cycle Shack

These Dual Exhaust Systems feature 1 3/4" O.D. head pipes with 2 1/2" O.D. mufflers. These mufflers include welded-in steel baffles and the entire exhaust is made from 16-gauge one piece steel. The beauty of these exhaust systems is that they will work with most aftermarket forward controls and all OEM forwards controls. Fits Sportster Evolution 1986/2003. Chrome Plated, Made in U.S.A.

Tapered - Part#:M91146 ... $229.82

Slash Cut - Part#:M91145 ... $229.82

Gooseneck Upswept style drag pipes for Evo Sportster by Paughco, 86/LPaughco Upswept style drag pipes for Evo Sportster - This 1 3/4 inch O.D. 16 gauge Upsweep Gooseneck Drag Pipe Exhaust Set has angled ends with a slash cut. Includes hidden channel and tab mounting & T bolt. Also included is a custom mounting bracket and brake pedal stop. Instructions included. Fits Sportster Evolution 1986/2003. Chrome plated. Made in USA.
Part#:M91314 - our price $391.60

Paughco Upswept  Gooseneck Drag Pipe Exhaust Set for Ironhead Sportster.  Fits 57/78, and rigid frame 80/85Paughco Upswept drag pipe set for Ironhead Sportster - This 1 3/4 inch O.D. upsweep gooseneck drag exhaust set fits Ironhead Sportster 1957/1978, 1980/1985 in rigid frame only. Tab mounting with frame clamp included. Chrome plated. Made in USA.
Part#:M90086 - our price $276.64

Cycle Shack slash cut drag pipes for Evo Sportster, 40" long, 86/LCycle Shack Slash Cut drag pipes for Evo Sportster - These 40 inch long classic style Drag Pipe Exhaust sets can be used with highway pegs without any clearance problems. Use with your existing mounting bracket or our MU95418 chrome plated bracket. The 1 3/4 inch O.D. exhaust sets can be used with your existing heat shields or our MU95322 and MU95323 custom heat shields from Cycle Shack. These sets will fit models with forward controls. Fits Evolution Sportster models 1986/2003. CYCLE SHACK Chrome Plated Classic Drag-1 3/4 inch O.D. Chrome Plated. Made in USA.

Part#:M90097 - our price $187.00

OPTIONAL: For 1986/Early 1987 models use #M95002 brake pedal stop. $3.71  (Please Note: Our minimum order is $35.00 total. Take advantage of our low Flat Rate Shipping and order everything you need now!)

Use MU95107 exhaust port clamps and retaining ring kit and MU94016 crush gaskets.

2 inch O.D. Slash Cut Drag Pipes for Evo Sportster from Cycle Shack.DRAG PIPE SETS FOR EVOLUTION SPORTSTER - Cycle Shack

These 40" long classic style Drag Pipe Exhaust sets can be used with highway pegs without any clearance problems. Use with your existing mounting bracket or our M95418 chrome plated bracket (sold below). Use our MU95338 and MU95339 (sold below) for the 2" O.D. exhaust set. These sets will fit models with forward controls. Fits Evolution Sportster models 1986/2003.

CYCLE SHACK Chrome Plated Classic Drag-2" O.D. - Part#: MU90098 ... $188.16

OPTIONAL: For 1986/Early 1987 models use #M95002 brake pedal stop. $3.71  (Please Note: Our minimum order is $35.00 total. Take advantage of our low Flat Rate Shipping and order everything you need now!)

Use MU95107 exhaust port clamps and retaining ring kit and MU94016 crush gaskets.

Cycle Shack Straight Cut Drag Pipes for Evo Sportster, 40 " long, 86/LCycle Shack Straight Cut drag pipes for Evo Sportster - These 40 inch long classic style Drag Pipe Exhaust sets can be used with highway pegs without any clearance problems. Use with your existing mounting bracket or our 95418 chrome plated bracket. The 1 3/4 inch O.D. exhaust sets can be used with your existing heat shields or our MU95322 and MU95323 custom heat shields (sold below) from Cycle Shack. These sets will fit models with forward controls. Fits Evolution Sportster models 1986/2003. " CYCLE SHACK" Chrome Plated Square Cut-1 3/4 inch O.D. Chrome Plated. Made in USA.

Part#:M90099 - our price $168.94 including shipping*

OPTIONAL: For 1986/Early 1987 models use #M95002 brake pedal stop. $3.71  (Please Note: Our minimum order is $35.00 total. Take advantage of our low Flat Rate Shipping and order everything you need now!)

Use MU95107 exhaust port clamps and retaining ring kit and MU94016 crush gaskets.

Paughco classis drag pipe exhaust set for 1979 Sportster, slash cut, Ironhead. 34" longPaughco Classic Drag Pipe Exhaust Set for 1979 Ironhead Sportster - This slash cut Drag Pipe Exhaust Set is 34 inch long with a 1 3/4" O.D. Fits Ironhead Sportster 1979 Electric Start Only. Chrome Plated. Made in USA.

Part#:M90110 ... $174.69

Exhaust Sheild for Evo Sportster with 1-3/4 outside dimension from Cycle Shack.

Chrome Plated Front Shield for XL Evolution exhaust pipes.

Take advantage of our Flat Rate Shipping and get everything you need now. 

Need Hardware?  Call us! 603-237-8200

EXHAUST HEAT SHIELDS FOR EVOLUTION SPORTSTER WITH 1 3/4" O.D. EXHAUST SYSTEMS - Cycle Shack


Combine safety and style with these exhaust heat shields.
These shields will not only protect your pants and boots but will conceal the bluing that is so common with high temperature exhaust systems.
Heat shields are complete with hose clamps and necessary mounting hardware.
Fits most custom 1 3/4" O.D. Evolution Sportster exhaust systems with OE style bends at the head pipe.


Part #: M95323 - Chrome Plated Rear Shield
Fits Evolution Sportster 1986/2003 ... $59.95

Part #: M95322 - Chrome Plated Front Shield
Fits Evolution Sportster 1986/2003 ... $59.95

EXHAUST HEAT SHIELD SETS FOR EVOLUTION SPORTSTERS WITH 2" O.D. EXHAUST - Cycle Shack

Provide protection for your sole and conceal your blues.
Each includes a pair of stainless steel hose clamps for easy installation.
Fits M90098 and any 2" exhaust pipes with O.E bends.

Part #: M95339 - Chrome Plated Rear Set,
Fits Evolution Sportster 1986/2003 ... $66.95

Part #: M95338 - Chrome Plated Front Set
Fits Evolution Sportster 1986/2003 ... $66.25

Insulating exhaust wrap from Cool It.

Insulating exhaust wrap.

Black insluating wrap shown installed.

Snap Straps for exhaust wrap.

Snap Straps

HI-Heat coating spray for insulating exhaust wrap.

Hi-Heat Spray Coating

Also found on Exhaust Accessories page

EXHAUST INSULATING WRAP FOR HEADER PIPES - Cool It®


Exhaust Insulating Wrap not only helps to protect you from dangerous pipe burns, it also increases horsepower and fuel efficiency.
Maintains hotter exhaust gases inside the pipe allowing them to exit faster due to decreased density.
Withstands temperatures up to 2000°F.
To secure the insulating wrap, use the cut-to-length Snap Strap Clamp Kit, included with wrap kit.
To protect the wrap and seal the pores, use the included Hi-Heat Coating after installation.
Includes Instructions.

 

Description of Kit Part # Price Buy Now
COPPER KIT includes 1 Roll copper impregnated wrap, 1 Box Snap Straps, 2 (11 oz)cans Copper Satin Hi-Heat Coating 95122-31-29 $106.58
BLACK KIT includes 1 Roll Wrap, 1 Box Snap Straps, 2 (11 oz)cans Black Satin Hi-Heat Coating 95121-31-23 $100.25
White (silver) KIT includes 1 Roll Wrap, 1 Box Snap Straps, 2 (11 oz)cans Aluminum Satin Hi-Heat Coating 95120-31-24 $97.31
Copper Impregnated Wrap 2'x50' 95122 59.45
Black Wrap 2' x 50' 95121 57.62
Black Wrap 2' x 25' 95146 36.36
White Wrap 2 x 50' 95120 54.04
Tan Wrap roll 2 'x 25' 95145 35.00

NOTE: 44 inches of wrap are required per foot of 2" diameter pipe, with a 1/4 inch overlap. Each roll will wrap approximately 13 ft. of exhaust pipe, depending on size of pipe and amount of overlap.

MOUNTING BRACKET FOR SPORTSTER OE EXHAUST

Part #: M95418 - Chrome plated. Fits Sportster Models 1980/Later. Note: Will not fit 883R 2002/Later. ... $32.75

More Exhaust Accessories can be found on their own page! Mufflers, Extensions, Universal Heat Shields, Insulating Wrap, etc.

FUEL PACKS FOR 2007 FUEL INJECTED MODELS

If you need more parts to finish your installation, please call us with a complete order to save money on shipping. View Online Catalog

More Sportster Specific Items and Links in The Sportster Pages.

Don't see what you need?  Contact us.  Chances are we have it.  We have thousands of parts that are not shown online.

15 Percent Coupon, summer promo, Beer Machine

FLAT RATE SHIPPING APPLIES IN CONTINTENTAL 48 UNITED STATES ONLY. AK, HI and APO/FPO will have additional shipping fees. We ship within the U.S.A. and to APO/FPO (military addresses; weight and size restrictions apply.). We do not accept foreign credit cards. Please see our CONTACT page for more information.

Prefer to call in your order to Steel Thunder? Call 603-237-8200.

FREQUENTLY ASKED QUESTIONS

Please note that all prices are subject to change.

***

Steel Thunder Custom Cycles

531 Bungy Road

Columbia, NH 03576

Copyright 2002-2013 Steel Thunder Custom Cycles©

 

Thank you for shopping at Steel Thunder Custom Cycles online motorcycle parts store!

 

 

 

Protected by Copyscape Duplicate Content Detection Software