©©
Wolf Daddy Parts List - This is not a complete list . Complete list will be available soon.
Frame
10-2 Shift Rod 1
5-17 Spring Plate 1
5-18 Stop 1
5-34 Neck Cups 2
9-73 Belt Guard 1
11-120 Tail Light/License Bracket 1
21-181 1/8” Pipe Fitting (Oil Filter/Regulator Mount) 2
21-185 90 Degree Fitting (Oil Filter/Regulator Mount) 2
25-138 Oil Filter/Regulator Mount 1
25-60 Oil Filter 1
47-280 Forward Controls (Polished Billet) 1
5-119 Pyramid Axle Adjusters 1
5-130 Rear Block Adjusters 1
5-148 Kickstand Mounting Bracket 1
5-149 Spring 1
83-13 Axle Slider Covers 1
85-183 Frame, Wide Rigid 1
96-840 ½” Offset Base Plate 1
96-841 ½” Primary Spacer 1
Front-End
8-16 Headlight 1
117-33 Fork Tube Assembly 1
27-162 Triple Tree Stem Nut 1
27-97 Dust Covers 1
29-72 Triple Trees (Polished Billet) 1
32-216 Front Axle 1
33-14 Axle Spacer (Front Wheel) 1
34-104 Top Clamp 1
34-89 Handlebar Bushings 1
35-2 Throttle Sleeve 1
35-55 Grips 1
41-432 Riser Bolts 1
47-196 Handlebar Controls 1
50-177 Handlebars 1
66-76 Brake Line Clamp 1
95-443 Neck Bearings 2
Wheels
2-27 21” Rim Strip 1
2-57 21” Inner Tube 1
32-191 Rear Axle Nut Kit 1
33-1 Axle Spacer 1
33-15 Axle Spacer (Rear Pulley Side) 1
33-4 Axle Spacer (Rear Brake Side) 1
36-328 21” Front Spoke Wheel 1
36-574 18”x 5 ½” Rear Spoke Wheel 1
41-756 Front Rotor Hardware 1
41-792 Rear Rotor Hardware 1
41-899 Pulley Fasteners 1
4-429 21” Avon Tire 1
4-498 18”x 200mm Avon Tire 1
58-380 1/4" Pulley Spacer 1
90-278 Rear Brake Rotor 1
90-365 Front Brake Rotor 1
94-380 65 Tooth Pulley 1
98-380 .080 Cam Shim (Use between 11-120 & Frame) 1
98-384 .100 Cam Shim (Use between 90-681 & Frame) 1
Brakes
17-44 Brake Switch 1
21-217 10mm Banjo 3
21-219 12mm Banjo (Front Master Cylinder) 1
21-228 Brake Line Fitting 1
21-229 Brake Line Fitting 1
21-354 10mm Banjo Bolt 3
49-238 Rear Brake Line 1
49-244 Rear Brake Line 1
49-254 Front Brake Line 1
90-345A 12mm Crush Washer 2
90-351 Brake Tee 1
90-675 Brake Caliper (Polished Billet) 2
90-676 Front Caliper Bracket 1
90-681 Rear Caliper Bracket 1
Motor & Driveline
201-45 5 speed Transmission 1
298-160 80ci Motor 1
298-98P Starter Bushing 1
3-189 Spark Plug 2
40-532 Primary Cover Screws 1
40-544 Exhaust Nut Kit 1
5-186 Motor Mount Hardware 1
5-218 Top Motor Mount 1
58-376 ½” Pulley Offset 1
58-511 Belt Drive 1
62-617 Exhaust Pipes 1
66-203 Exhaust Flanges 1
70-160 Starter Motor 1
70-181 Jackshaft Assembly 1
78-437A Primary Cover Gasket 1
78-441A Inspection Cover Gasket 1
88-66 Outer Primary Cover 1
88-120 Inner Primary Cover 1
89-112 Derby Cover 1
89-90 Inspection Cover 1
95-452 Snap Ring 2
95-751A Derby Cover O-Ring 1
95-800 Starter Bushing 1
96-442 Clutch Pushrod 1
96-801 Lock Tab 6
94-279 30 Tooth Transmission Pulley 1
58-350 128 Tooth Belt 1
Electronics
1-55 Battery 1
8-79 Tail Light 1
17-25 Ignition Switch Cover 1
17-60 Ignition Switch 1
18-108 Ground Cable 1
18-14 Wire Ties 20
18-231 Handlebar Harness w/Switches 1
18-257A Positive Battery Cable 1
18-346 Wire Harness 1
298-98K Ignition Rotor Bolt 1
5-129 Battery Strap 1
53-422 Ignition w/Coil & Plug Wires 1
53-491 Charging System 1
53-528 Ignition Rotor 1
78-322 Battery Tray 1
89-304 Point Cover 1
91-352 Ignition Plate Stud 2
Tanks & Fenders
11-91 1.5" Spacer (Rear, Bottom Fender Mount) 1
104-35 Fender Brace 1
19-151 Rear Fender 1
19-61 Front Fender 1
20-38 Gas Tank 1
21-1 Worm Clamp 2
21-134 Petcock 1
21-263A ¼” Hose End 2
21-264A 3/8” Hose End 8
26-112 Oil Tank (Chrome) 1
5-132 Rubber Mount (Oil Tank) 4
71-141A ¼” Stainless Steel Gas Line 1’
71-144 3/8” Stainless Steel Oil Line 6’
76-450 Solo Seat 1
66-52 Rear Fender Mount 1
Cables
48-577 Throttle Cable 1
48-602 Idle Cable 1
48-662 Clutch Cable 1
All the Hardware necessary to assemble the kit. All nuts, bolts and washers.